In wake of Hurricane Sandy, disinfect contaminated wells

live.psu.edu/story/62416#nw69
Monday, November 5, 2012

UNIVERSITY PARK, Pa. — As the Northeast begins the recovery process in the wake of Hurricane Sandy, a water-quality specialist in Penn State’s College of Agricultural Sciences is urging those who rely on private water supplies to guard against possible flood contamination of their wells.

In areas where flooding occurred, well owners should disinfect these water supplies before drinking water from them, according to Bryan Swistock, water resources extension associate.

“Hundreds if not thousands of water wells may have been flooded or affected by runoff from this storm,” said Swistock. “In addition to seeing flood water around their wells or springs, homeowners also might notice increased sediment in their water. Even after this goes away, bacteria still may contaminate the water supply.”

Swistock noted that a simple coliform bacteria test from a water-testing lab can determine if the water supply is safe to use or if disinfection is needed. “If residents suspect that their wells may be contaminated,  they should contact their local or state health department for specific advice on disinfecting them,” he said.

Swistock said local well drillers and contractors should be contacted to inspect well components, and he urged residents to follow the suggestions below — found on the U.S. Environmental Protection Agency website at http://www.epa.gov/safewater/privatewells/whatdo.html — for dealing with a water well that likely was flooded:

— Well and pump inspection: If flood conditions are known to have occurred or are suspected at a well, the well and pump should be inspected. Swiftly moving flood water can carry large debris that could loosen well hardware, dislodge well construction materials or distort the casing. Coarse sediment in the flood waters could erode pump components. If the well is not tightly capped, sediment and flood water could enter the well and contaminate it. Floods also may cause some wells to collapse.

— Check the electrical system. After flood waters have receded and the pump and electrical system have dried, do not turn on the equipment until the wiring system has been checked by a qualified electrician, well contractor or pump contractor. If the pump’s control box was submerged during the flood, all electrical components must be dry before electrical service can be restored. Get assistance in turning the pump on from a well or pump contractor.

— Monitor pump operation. All pumps and their electrical components can be damaged by sediment and flood water. The pump, including the valves and gears, will need to be cleaned of silt and sand. If pumps are not cleaned and lubricated properly, they can burn out. Get assistance from a well or pump contractor, who will be able to clean, repair and maintain different types of pumps.

— Emergency disinfection of wells that have been flooded. Before disinfection, check the condition of the well. Make sure there is no exposed or damaged wiring. If you notice any damage, call a professional before the disinfection process. Materials needed include at least a gallon of nonscented household liquid bleach, rubber gloves, eye protection, old clothes and a funnel.

To disinfect, follow these steps:

— If the water is muddy or cloudy, use a hose to run the water from an outside spigot until the water becomes clear and free of sediment.

— Determine what type of well you have and how to pour the bleach into the well. Some wells have a sanitary seal with either an air vent or a plug that can be removed. If it is a bored or dug well, the entire cover can be lifted off to provide a space for pouring the bleach into the well.

— Mix a gallon of bleach with a few gallons of water. Carefully pour the bleach mixture down into the well casing, using a funnel if needed.

— After the bleach has been added, run water from an outside hose into the well casing until you smell chlorine coming from the hose, then turn off the outside hose. If chlorine odor never develops at the faucet,  you may need to add more bleach to the well.

— Turn on all cold water faucets, inside and outside of the house, until the chlorine odor is detected in each faucet, then shut them all off. If you have a water treatment system, switch it to bypass before turning on the indoor faucets.

— Wait six to 24 hours before turning the faucets back on. It is important not to use this water for drinking, cooking, bathing or washing during that time period — it contains high amounts of chlorine.

— Once the waiting period is up, turn on an outside spigot with hose attached and run the water into a safe area where it will not disturb plants, lakes, streams or septic tanks. Run the water until there is no longer a chlorine odor. Turn the water off.

The system now should be disinfected, and you can use the water. However, the water should not be used for drinking until a bacteria test indicates that the disinfection procedure was effective. Have the water tested for bacteria seven to 10 days after disinfection.

To assist owners of private water supplies in the Berks County (Pa.) area, Penn State Extension will offer a Safe Drinking Water Clinic on Nov. 7 at the Berks County Agricultural Center, 1238 County Welfare Road, Leesport. The clinic will take place from 2 to 4 p.m. and will be repeated from 6 to 8 p.m.

Attendees will learn about proper location, construction, testing, maintenance, protection and treatment of private drinking water supplies. The $10 per person/household registration fee will include testing of one water sample for pH, total dissolved solids, nitrate, total coliform bacteria and E. coli bacteria. To learn more or register for the clinic, visit the Web at http://psu.ag/RsWL0N online.

For more information on flooded-well safety, download the free Penn State fact sheet, “Shock Chlorination of Wells and Springs,” at http://psu.ag/RujwBe online.